TIG Tack Welding Complete Guide: From Setup to Perfect Tacks

Tack welding uses small, localized welds to hold parts in position before final welding. A well-placed tack secures alignment, prevents distortion, and helps the final weld go smoothly. Compared with other processes’ tack welding, TIG tack welding provides low-amperage control and a concentrated arc, resulting in more accurate, cleaner tacks—well suited to thin materials and applications where appearance and quality matter. This guide explores the different types of TIG tacks, how to apply them across joints and positions, step-by-step tacking, common problems with solutions, and how modern TIG machines improve consistency while reducing defects.

Table of Contents

Types of TIG Tack Welds (and When to Use Them)

TIG welding can be divided into DC TIG and AC TIG:

  • DC TIG is used for carbon steel, stainless steel, alloy steels, and most other metals. Both fusion tacks and filler tacks can be applied.
  • AC TIG is used for aluminum and aluminum alloys. Filler is usually required to avoid lack of fusion or cracking.

After selecting the correct power mode based on the material, you can then choose the specific tack welding type.

By Operation Method

  • Fusion Tack (No Filler): Best for thin sheet (about 1–2 mm) with near-perfect fit-up (gap < 0.5 mm). Avoid on aluminum or thicker sections due to risk of cracking or weak fusion.
  • Tack with Filler: Stronger and more reliable; suitable for gaps, thicker sections (up to ~6 mm), and aluminum.

By Machine Feature

  • Manual TIG Tacking: Full control via pedal ortorch; versatile but requires high skill.
  • Semi-Automatic Tack(Assisted Spot): Preset current and time (in milliseconds) for repeatable, low-heat tacks; ideal in precision sheet metal fabrication.

Joint- and Position-Specific Tips

  • Outside Corner:Highly heat- Ensure a tight fit-up and use an appropriate tack current; keep heat input time as short as possible—without compromising tack quality—to avoid weld defects.
  • Butt Joints:Use balanced sequence to prevent closing the opposite end.
  • Lap Joints:Focus heat on bottom plate; filler tacks improve strength.
  • T-Joints/Fillet Welds:Usually require filler for penetration and strength; adjust torch angle for access.
  • PipePositions
    • Position filler toward pipe interior to counteract gravity
    • Start at the top (12 o’clock) and move downward; plan tacks to shrink toward tighterareas.

How to Perform TIG Tacks (Step by Step)

Preparation

Safety First

  • Wear an auto-darkening welding helmet (shade 10–13), thick leather gloves (that allow for finger dexterity), and cover all skin with flame-resistant clothing.
  • Ensure good airflow; remove flammables; keep an extinguisher accessible.

Metal Preparation

  • Workpiece Cleaning:Thoroughly remove all grease, dirt, paint, scale, and rust.
    • For Stainless Steel:Use stainless-only brush or dedicated abrasives to avoid cross-contamination.
    • For Aluminum:Use a stainless steel brush dedicated solely to aluminum and brush in one direction to break up the oxide layer.
  • Edge Treatment:Remove burrs and dress edges for tight fit-up.

Fit-up

  • Clampand support. For fusion tacks (no filler), fit must be near-zero gap.
  • Use rigid fixturesto apply positive restraint and prevent distortion; when necessary, tack the assembly to a welding platen to hold dimensional stability.

Equipment and Consumables Setup

  • Machine Settings and Filler Selection:
    • Select the welding mode(AC/DC)and filler classification according to the base metal, and match welding current and tungsten diameter to material thickness; see the reference tables for specifics.
  • Tungsten Preparation:
    • 2% Lanthanated (blue) tungstenis the best all-around choice for TIG tack welding.
    • For DC, grind to a sharp point; for AC, form (or allow) a stable ball on the tip.
  • Shielding Gas:
    • Use ≥99.99% argon or helium; typical flow 8–15 L/min. Increase flow when using large cups,gas lenses, or in drafty conditions. Set pre-flow to 0.5~1 s and post-flow to 8~12 s to protect the tack and hot tungsten.
  • Filler Usage:
    • Tack weld with filler for stronger tacks, bridging minor gaps, or when tacking aluminum. Fusion tack (no filler) used for thin materials with tight fit-up.

Starting the Tack

  1. Position hands comfortably, steady the torch.
  2. Hold torch at 15–20° push angle, adjust for joint types.
  3. Keep tungsten stick-out about 3-5mm from the metal; adjust with cup size/gas lens/access.
  4. Use higher current (1.5~2×normal welding current) for tacks with rapid ON/OFF(2T)
  5. Add filler (if needed): For aluminum, use quick dip-and-withdraw dabs to limit cooling and oxide contamination; for stainless or carbon steel, use single dabs or a short continuous feed.
  6. Terminate arc fast (milliseconds), keep post-flow for shielding.
  1.  

Tacks Placement, Sequence, and Spacing

Sequence

  1. Tack both ends → one in the center → subdivide remaining spans; alternate sides to balance heat.
  2. Never proceed linearly end-to-end; that accumulates shrinkage and distortion.

Spacing

  • Thin Sheet (< 3mm):50–100mm apart
  • Medium Thickness (3–6mm):100–200mm apart
  • Thick Sections (> 6mm): Up to 300–400mm apart

Note: For stainless steel, use closer tack spacing for better control distortion.

These are best-practice guidelines; actual shop conditions vary, so adjust to suit the specific welding procedure.

Post-Weld Inspection and Finishing

  1. Visual inspection for cracks, porosity, undercut, lack of fusion, or crater/shrinkage cavities.
  2. Check alignment to ensure parts remain properly positioned
  3. Grind away raised tacks on thick material if needed.

Common TIG Tack Welding Problems & Solutions

Problem

Cause

Solution

Cracking

Too small, no filler, fast cooling, mismatch between the filler and base metal

Add filler, increase size, add more tacks, select the correct filler metal

Poor Fusion

Low current, long arc, poor fit

Increase current, shorten arc, improve fit-up

Burn-Through

Excessive heat, long arc-on time

Lower current and cut arc-on time, tighten the joint gap, blunt sharp edges, use a ceramic backing (for backside support), and add copper/aluminum chill bars.

Contamination

Dirty metal, poor gas, tungsten touch
Dirty base metal or filler wire, inadequate shielding gas purity, insufficient post-flow, tungsten tip dip

Thoroughly clean base metal and filler wire, use high-purity shielding gas, extend post-flow time, regrind the tungsten electrode

Distortion

Wrong sequence, weak clamping

Balance sequence, use more tacks, improve fixturing

Inconsistent Size

Hand timing variations

Use assisted spot/tack mode or practice consistency

How Modern TIG Machines Improve Tack Welding

The toughest challenge in TIG tack welding is heat control, especially on thin metals. Many defects—fusion failure, burn-through, distortion, or uneven tack size—mainly come from poor heat input management.

Modern TIG machines address this with dedicated spot/tack modes. For example, the JASIC EVO20 TIG series uses Assisted Spot/Tack feature for thin sheet metal, using a brief high-current pulse to create small, consistent welds with low heat input, reducing burn-through and deformation compared to traditional TIG tacking. See this 30-second EVO20 TIG tacking video.

Let’s compare:

A
B

Comparison

Standard TIG Tack (A)

EVO20 TIG Tack (B)

Arc Ignition Success

~85% (inconsistent starts)

99.9% (consistent and instant starts)

Weld Bead Consistency

Varies by hand control

Uniform, repeatable

Post-Weld Processing

Requires grinding, pickling

Minimal or none

Conclusion

TIG tack welding is a small procedure with a big impact. With the right setup and sequence—clean prep, correct current, and balanced tack placement—strong, clean, reliable tacks make final welding easier and low-distortion. Modern assisted tack modes further boost consistency, quality, and efficiency, especially on thin sheet.

Click to explore the JASIC EVO20 TIG series

Frequently Asked Questions (FAQ)

Q: What current should I use for TIG tack welding?

A: Use 1.5-2 times your normal welding current. For example, if you normally weld at 100A, use 150-200A for tacking.

A: Depends on the application. Use filler rod for aluminum, thick materials, or any joint with gaps. Fusion tacks work for thin metal with good fit-up.

A: Usually due to tacks being too small or cooling too quickly. Add filler rod for strength and consider making slightly larger tacks.