What’s the difference between a tack weld, a spot weld, and a Arc spot weld? How do you tack weld different materials properly? If you’ve ever wondered about the right technique, placement, or troubleshooting for tack welds, you’re not alone. In this guide, you’ll learn what tack welding is, how it compares to spot welding, the different types of tack welds, how to do it correctly on various materials, and what mistakes to avoid.

1. What Is Tack Welding?
Tack welding means making small, temporary welds to keep metal pieces in the correct position before final welding. These short welds help maintain alignment and prevent movement or distortion, but they are not meant to support loads or be part of the finished structure.1.1 Tack Weld vs. Spot Weld vs. Arc Spot Weld: What’s the Difference?
What They Have in Common: When we talk about “spot welds”, we may mean either resistance spot welds (made with pressure and electric current) or Arc spot welds (created using a MIG/TIG welder’s timed spot mode). Along with tack welds, these are all small, localized welds commonly used in metal fabrication and assembly. Each helps join metal parts, aids in positioning or alignment, and is widely used in automotive, repair, and manufacturing settings.
How They Are Different:
| Aspect | Tack Weld | Resistance Spot Weld | Arc Spot Weld (MIG Spot Welding Mode/Cold TIG) |
| Purpose | Temporary hold for alignment before final welding | Permanent joining of overlapping thin sheets | · Ideal for tack welding thin plates. · Ensures consistent spot welds on sheet metal. |
| Process | Arc welding (MIG, TIG, Stick) with filler metal | Pressure and electric current, no filler metal | MIG/TIG welder in spot mode, timed arc, no hole needed |
| Appearance | Small bead or dot, usually on edge/seam | Small, round, flat dimple, usually in middle | Small, round bead or dot Consistent in size and shape |
| Strength | Temporary, not load-bearing | Permanent, load-bearing | Permanent, load-bearing |
| Adjustable | Yes, can break and reposition before final weld | No, joint is permanent | No, joint is permanent |
| Typical Use | Frames, pipes, structural setup | Car panels, appliances, thin metal (factory) | Car panel repair, thin sheet, grid metal, DIY/repair |
Tack welds are for temporary alignment and adjustment, while both resistance spot welds and Arc spot welds are for permanent joining of metals—using different equipment and processes, but achieving similar results in terms of strength and appearance.
2. Three Kinds of Tack Welding
When it comes to tack welding, there are three main methods commonly used in metal fabrication:- Standard Tack Weld: A small, temporary weld used to hold parts in position for final welding. Best for general fabrication, assembly, and situations where parts fit together well and precise alignment is needed.
- Bridge Tack Weld: Used when there is a gap or misalignment between parts. Bridge tacks are placed across the gap to help pull pieces together and align them before the final weld is made. Ideal for correcting misaligned or warped joints, especially in sheet metal work or repairs where gaps must be closed before final welding.
- Hot Tack Weld: This method involves applying extra heat and filler metal to the joint, sometimes followed by hammering to close a gap. Hot tacks are useful for quickly drawing parts together but may not always meet high-quality standards. Used in heavy fabrication, repair work, or when large gaps or severe misalignment must be closed quickly and other methods aren’t practical.
3. Tack Welding Best Practices

3.1 How Many Tacks Are Enough?
The number of tack welds should be sufficient to keep parts properly aligned and stable during welding. There is no universal code requirement for maximum spacing, but as a common shop practice, tacks are often spaced:- Thin material (generally less than 3 mm):50–100 mm
- Medium thickness (3–6 mm):100–200 mm apart.
- Thick sections (over 6 mm):Up to 300–400 mm apart.
3.2 How to Tack Weld Steel
- Keep Tacks Small:
- For thin steel (typically less than 3 mm), tacks are usually 6–10 mm long;
- For medium to thick steel (3–6 mm and above), tacks may be 10–20 mm,
- Even Spacing:Place tacks evenly along the joint to prevent misalignment—closer together for thin steel, farther apart for thick.
- Sequence Matters:Start at the center and alternate sides to control heat buildup and minimize warping.
- Check and Adjust:After tacking, check alignment. Tacks can be broken and redone if needed before final welding.
3.3 How to Tack Weld Stainless Steel
- Use Stainless Filler:Always use stainless wire or rod for tacks to maintain corrosion resistance.
- Minimize Heat:Make tacks as quickly as possible to avoid warping and discoloration.
- Shield Well:Ensure good gas coverage to prevent oxidation and contamination.
- Cleanliness Counts:Use a stainless-only brush to clean before tacking—contamination can ruin the weld.
3.4 How to Tack Weld Aluminum
- Tight Fit-Up:Ensure parts fit tightly with no gaps—aluminum tacks are weak if gaps exist.
- Quick, Hot Tacks:Use higher amperage and make tacks fast to avoid melting edges or excessive distortion.
- Clean Oxide:Always brush off oxide just before tacking for best fusion.
- Add Filler:Use filler rod for stronger tacks, especially if the fit isn’t perfect.
3.5 Common Mistakes to Avoid
- Improper tack placement:Tacks too far apart can lead to misalignment; too close can cause distortion.
- Incorrect heat settings:Too much heat burns through thin materials; too little results in weak tacks.
- Poor material preparation:Dirty or contaminated surfaces cause weak or defective welds.
- Ignoring alignment checks:Always check alignment after tacking to avoid costly rework.
4. FAQs
Q1: What is a tack weld?
A tack weld is a small, temporary weld used to hold metal parts in place before final welding.
Q2: What’s the difference between a tack weld and a spot weld?
Tack welds are used for temporary alignment and adjustment, while spot welds—which can refer to both resistance spot welds and Arc spot welds—are used for the permanent joining of metals.
Q3: Is tack welding strong?
Tack welds are strong enough for assembly, but not for permanent or load-bearing use.